Number 2 uses ..—, while number 3 uses …–. The difference is that it’s a dash in 2 and a dot in 3.
All the digits used in Morse Code Numbers can be compared.
Yes! Click the Copy Code link at the top of this page to get a copy of …–. You don’t have to type the symbols into Morse code and can place it in messages, documents, or compatible Morse code software.
In Morse code, the number 3 is the following: three dots (..-), a total of five signals. Note that in Morse code, the number 3 has both dots and dashes; the number 0 has only dashes.
In morse code, number 3 is the following: three dots (..-), a total of five signals. Note that in Morse code the number 3 has both dots and dashes; the number 0 in Morse code has only dashes.
To say 3 in Morse code, use the rhythm di-di-di-dah-dah. The first three short sounds are followed by two longer sounds. A “dah” takes three times as long as a “di.
Find clear answers to common questions about reading, writing, and learning 4 in Morse Code
Draw the number 4 and then use it to show 4 dots for remembering 4. Use four dots that point towards a last dash.
It is easy to remember the Morse code sequence for numbers 1-5; they form a handy mnemonic. Each number is placed with the number of matching dots, and each cell is blank if the number value does not match the corresponding dots.
| Number | Morse Code | Memory Clue |
|---|---|---|
| 3 | …– | 3 dots + 2 dashes |
| 4 | ….- | 4 dots + 1 dash |
| 5 | ….. | 5 dots + 0 dashes |
See that the next number can be written without leaving any dashes, without adding any dots. This makes Mori・s 4 easy to remember, because it is only one step away from Mori’s 5.
You can use this relation to remember this sequence of numbers rather than memorising each number, one by one.
Remember at a glance by doing a little homework.
Suppose that you see …: Number 5 – Morse code type.
Without referring to the table, see if you can turn it into number 4’s pattern.
P.S. Hint: Only one of the signals needs to be changed.
Answer: Change 5 with a dash. The answer is: The answer is the number 4….-.
Next, for a change, begin with number 3 (…–) and substitute the 4th signal with a dot. The same result will be obtained.
Memory tip: Remember the phrase “Four dots, one dash to finish.” With this pattern memorized, it can be recalled easily and recognized as a relationship with the adjacent Morse code digits.
The sound of 4 in Morse code begins with four quick beeps and ends with one longer tone. Its rhythm is di-di-di-di-dah, making it easy to recognize once you become familiar with the change in signal length.
Unlike spoken numbers, Morse code does not depend on a person’s voice. It can be transmitted through sound, light, or electrical signals. The important part is the length and order of each signal, not its pitch.
The Morse code for 4 is pronounced in the same way as”di” on 4 signals, with the last “dah” kept longer.
The timing is according to three simple rules:
Suppose the time unit is set to be 0.1 seconds, then the four short tones add up to 0.4 seconds of time. The final longer tone is another 0.3 s, and the four pauses are 0.4s each.
At this speed, this will be 4 full Morse code characters in 1.1 seconds with no delay between each character.
You can send at various speeds, but there must be a consistent timing relationship.
An understanding of rhythm is beneficial (but not essential), but also a recognition of rhythm without looking at the symbols.
The following is a brief challenge to listen:
The last long tone is usually not heard. Wait until the entire character has been stated before making your guess on the number.
For more formal listening training, check out the ARRL Morse Code Learning Resources, including listening exercises and training for beginning listeners.
The Morse code for 4 is a dotted pattern of four dots then a single dash (….-). The full sequence will be written: ….-, with no blank spaces between the symbols.
Do the following:
Example: How to Write 42 in Morse Code
What will you type on a computer keyboard to send the number 42 using Morse code? What would you type on a computer keyboard to send the number forty-two in Morse code?
Convert the numbers individually:
When it is completed, the total number is:
….- ..—
On the left is the gap between the two groups. It is considered to be marking the end of one digit and the beginning of another.
If there is no clear delineation of each character, the receiver may be confused about which numbers to listen to.
How to Type and Copy 4 in Morse Code
The Morse Code keyboard and special software are not necessary to type 4 in Morse code. For most purposes, just the standard keyboard will do the trick.
There are two typical patterns in which this is displayed:
They both have the same Morse Signal sequence. The keyboard version is usually easier to use for text-based translators, as some Morse tools might not recognise the decorative Morse symbols.
To obtain a copy of 4 in Morse code, just click the Copy Code button at the top of this page. The sequence can then be entered into a text message, document, or a compatible Morse code decoder.
Common pitfall: DO NOT put a space before the last dash! The dots “….” are typed as if they were two separate digits 4.
The symbols are written adjacent to each other so that it’s clear they are part of the same code.
In Morse Code, numbers and letters each have their own code. For Morse Code, the number 4 is a single character that may be used in conjunction with letters in messages, measurements, and numeral information.
The standard gives each number from 0 to 9 a different pattern according to the International Telecommunication Union (ITU).
For instance, the message gate 4. The word Gate is received letter by letter; the number 4 is received using the numerical sequence that 4 follows.
But in Morse dots, dashes and spaces themed to the word “FOUR” will need four dots and dashes, namely F, O, U and R.
Another point of interest is the resemblance of the letter “H” to the numeral “4”. Both start with four dots, but end differently:
The final quarter of a mile is the critical distance! Dashes added before the letter or character alter the signal into the digit 4 for the transmitting user to be read out by the receiving person when they have reached four dots.
This point is important when decoding Morse code, so it doesn’t confuse letters with numbers.
Four dots • One dash
di-di-di-di-dah