Number 2 uses ..—, while number 3 uses …–. The difference is that it’s a dash in 2 and a dot in 3.
All the digits used in Morse Code Numbers can be compared.
Yes! Click the Copy Code link at the top of this page to get a copy of …–. You don’t have to type the symbols into Morse code and can place it in messages, documents, or compatible Morse code software.
In Morse code, the number 3 is the following: three dots (..-), a total of five signals. Note that in Morse code, the number 3 has both dots and dashes; the number 0 has only dashes.
In morse code, number 3 is the following: three dots (..-), a total of five signals. Note that in Morse code the number 3 has both dots and dashes; the number 0 in Morse code has only dashes.
To say 3 in Morse code, use the rhythm di-di-di-dah-dah. The first three short sounds are followed by two longer sounds. A “dah” takes three times as long as a “di.
Find clear answers to common questions about reading, writing, and learning 3 in Morse Code
One easy way to master the Morse code for 3 is to recall that it is a “clue” code: three dots then two dashes. You will have a way to think of the pattern without bouncing to a Morse code chart.
But here’s another handy little thing you can do. Number 3 is between 2 and 4, with the pattern of Morse code being predictable.
| Number | Morse Code | Easy Reminder |
|---|---|---|
| 2 | ..— | 2 dots + 3 dashes |
| 3 | …– | 3 dots + 2 dashes |
| 4 | ….- | 4 dots + 1 dash |
Take out the count of 2 and 3, removing one dash and adding one dot. What to do 3 to 4 is the same as what to do 4 to 5.
This forms a very easy Morse number pattern – the dots are getting longer, and dashes are getting shorter.
Time for a quiz!
Now if you see the Morse code for number 4: …..-.Now say that you see the Morse code for number 4: …..-
Now, try to turn it into the pattern for number 3—without looking at the table.
Hint: You must use 1 fewer dot and 1 more dash.
Answer: Replace the fourth dot with a dash (:). The answer is …– meaning number 3.
Now do this exercise, but go in the opposite direction and use number 2 instead, and change an element of the third signal from a dash to a dot.
Suggestion to remember:
Consider number #3 as the middle number between 2 and 4. On the other hand, persevere and memorize the way the patterns shift, and learning to remember the Morse code for 3 is easy!
There is a distinct change in rhythm for 3 in the Morse code pronunciation of the word. It starts with a rapid series of beeps, followed by two longer beeps at the end. Variations in the signal length enable listeners to recognise the number without observing the signal’s conventional pattern.
One tricky thing is that Morse changes the duration of the signal and not the pitch. Both short and long tones may be pitched exactly similarly and possibly at the same loudness. It’s the duration of each signal and the pauses in between:
Say 3 in Morse code: di-di-di-dah-dah. Quickly say each di and then ens is you say each dah about 3 times as long.
It all serves the timing of the move;
Let’s say that one time unit is 0.1 seconds; the three short tones are 0.3 seconds, and the two longer tones are 0.6 seconds. There are 0.4 seconds of silent gaps, for a total of four (x4 x 0.4 = 1.6).
At this speed, it takes 1.3 seconds for the entire Morse code message for number 3, not including the break between numbers.
The speed at which the short tones are sent, long tones are sent, and the gaps between them can be increased or decreased, but the count or relationship between short tones, long tones, and gaps needs to be consistent.
While it is beneficial to be able to read Morse code, it is also a key skill to recognize Morse code by sound.
Bear in mind that you need to listen to the audio at the top of this page first. On your first attempt, listen for the time between the quick signals when they turn into longer signals.
Then, play the sound again without reading the text code. Use fingers to practice tapping the rhythm.
Lastly, listen again and state the number without counting all the beeps. If you practice enough, you can start to recognize the entire sound pattern naturally.
Get more listening practice with the American Radio Relay League’s Morse Code Learning Resources. These include the option of an audio practice test that may assist novices in building their listening skills.
In Morse code, 3 is written as three periods (…) and the next two hyphens (–). Maintain symbols in the correct sequence, forming . . . –.
To write the number properly, one should follow this procedure:
Example: How to Write 303 in Morse Code
Now, suppose that you would like to encode the number 303 in Morse code.
The whole sequence is now:
…– —– …–
These groups of digits each correspond to one digit. If the spaces are not included, a reader or Morse code decoder may not be able to determine where one letter ends and the next begins.
Special keyboard is not required to type in Morse code 3. In most Morse code programs using text, regular periods and hyphens can be used.
You’ll find the symbol in two formats:
They both show the same pattern of signals, but some translators only understand the normal characters on the keyboard.
If it’s a quick 3-in-Morse-code copy and paste, click on Copy Code at the top of this page. The output can now be pasted into a message, a document, or an online Morse transcriber.
Note: When copying the Morse code from a web page, be sure that the symbols don’t get drawn as stylistic dots or dashes that your translator doesn’t understand.
In International Morse Code, every number has its own signal pattern. In Morse code, the number 3 is a single sign and can be differentiated from letters and other numerals.
For instance, the word Room (R-O-O-M) is being transmitted as individual letters, and the digit 3 (T-T-T) is being sent as a whole Morse character.
But the case is different for writing “THREE” in Morse code. It needs five distinct letter patterns (T, H, R, E, and E), rather than the letter pattern required for the number.
The other helpful fact is that the first three forms of signal S (…) have the same three signals as the digit 3 (…–). Each of the last two dashes indicates the difference between the number and the letter.
The International Telecommunication Union (ITU) has devised Morse code patterns for the letters, as well as the numbers. This makes it easier for receivers to determine which characters are meant when reading a full message.
Three dots • Two dashes
di-di-di-dah-dah